Cisco 640-460 Exam - PassITexam.com
Free 640-460 Sample Questions:
Q: 1 You are CCNA VOICE associate in xxyyinc.com. You need configure a voice
port that will allow the gateway to terminate 23 or 30 circuits from the PSTN. Which type of voice port
you will configure?
C. PRI T1/E1
Q: 2 Which of the following is selected first for an incoming dial peer?
B. incoming called-number
D. pots port
Q: 3 Power over Ethernet (PoE) is the ability for the LAN switching infrastructure
to provide power over a copper Ethernet cable to an endpoint (Powered Device). This capability, once
referred to as "inline power", was originally developed and first delivered by Cisco in 2000 to support
the emerging IP Telephony deployments. IP Telephones, like desktop PBX phones, need power for their
operation and Power over Ethernet enables scalable and manageable power delivery and simplifies
deployments of IP Telephony. As Wireless networking emerged, Power over Ethernet was also used to
power these devices to allow for deployments in locations where local power access did not exist. While IP
telephones and wireless access points are the most intuitive uses for PoE, the advent of 802.3af
standardization of PoE opens the door to a new generation of networked-attached devices such as video
cameras, point-of-sale devices, security access control (card scanners), building automation and
industrial automation just to name a few. When a Cisco switch supply PoE to an IP phone?
A. whenever switch and IP phone are Cisco products.
B. when Cisco switch supports prestandard PoE and the IP phone supports 802.3af.
C. when Cisco switch and IP phone both support a common PoE method.
D. Only when both the switch and IP phone use 802.3af PoE.
Q: 4 What is the default VTP mode on Cisco switches?
Q: 5 Which codec is less processor intensive?
Q: 6 Which Cisco Unified Communications layer is the call processing layer?
A. Layer A including video,communications client, software-based phones, IP Phone
B. Layer B including Voice mail,Presence,Contact Center
C. Layer C including Cisco Unified Communications manger,Directory Server.
D. Layer D including Gateway, Router, Switch.
Q: 7 What are the three VTP modes on Cisco switches?
Answer: B, C, D
Q: 8 A SIP Trunk is a logical connection between an IP PBX and a Service
Provider's application servers that allows voice over IP traffic to be exchanged between the two. When a
call is placed from an internal phone to an external number, the PBX sends the necessary information to
the SIP Trunk provider who establishes the call to the dialed number and acts as an intermediary for the
call. All signaling and voice traffic between the PBX and the provider is exchanged using SIP and RTP
protocol packets over the IP network. Which two statements about SIP trunk are true?
A. A SIP trunk configuration is mandatory for a UC500 device.
B. A SIP trunk is needed for internet access
C. A SIP trunk is needed only for voice if you are planning on using VoIP through a service provider.
D. A SIP trunk is not supported in a keyswitch configuration.
Answer: C, D
Q: 9 You are CCNA VOICE associate in xxyyinc.com. One user from your
company wants to use a signaling protocol on the voice gateways that require registration with the Cisco
Unified Communications Manager. Which protocol should you suggest to him?
B. Frame relay
Q: 10 An analog telephone is connected to a _______ port on a router?
Q: 11 Which protocol provides VoiP packet sequence numbering?
Q: 12 Time-Division Multiplexing (TDM) is a type of digital or (rarely) analog
multiplexing in which two or more signals or bit streams are transferred apparently simultaneously as
sub-channels in one communication channel, but are physically taking turns on the channel. Which is the
best description of time-division multiplexing?
A. One TDM frame consists of multiple timeslot per sub-channel.
B. the time domain is only one recurrent timeslots of fixed length
C. Individual source signals are combined into a composite signal, which allows a capacity equal to or greater
than the sum of the component signals.
D. All sources get an interleaved slice of time, which offers the entire frequency range allocated for that
Q: 13 What is required to convert a G711ulaw call to G729?
A. Voice Termination resources
B. Conferencing resources
C. Converter resources
D. Transcoding resources
Q: 14 Whhich statement is true abou the difference between voice VLAN and native
A. Voice VLAN uses untagged frames whereas native VLAN uses 802.1Q frames
B. Voice VLAN uses tagged 802.1Q frames whereas native VLAN uses 802.1P frames
C. Voice VLAN uses tagged 802.1Q frames whereas native VLAN uses untagged frames
D. Voice VLAN uses untagged frames only when no PCs are connected behind the phones whereas native
VLAN always uses untagged frames
Q: 15 Cisco ____protocol is used to inform the IP phone of its voice VLAN ID.
Q: 16 What is the maximum number of phones are supported on Call Manager
Q: 17 You are CCNA VOICE associate in xxyyinc.com. Which value should you
assign to option 150 for DHCP to operate correctly in a Cisco Unified Communications Manager Express
A. FTP server of the DNS server
B. MAC address of the DHCP server
C. MAC address of the TFTP server
D. IP address of the TFTP server
Q: 18 Please match the protocol to the characteristic.
A. (I)-(1 2);(II)-(3 4)
B. (I)-(2 4);(II)-(1 3)
C. (I)-(1 4);(II)-(2 3)
D. (I)-(1 3);(II)-(2 4)
Q: 19 What protocol needs to be enabled on an ATA if a fax machine is connected to
Q: 20 You are CCNA VOICE associate in xxyyinc.com. Which two are considered
endpoints in a Cisco Unified Communications solution?
B. call agent
C. IP telephone
Answer: C, D
Q: 21 I You are CCNA VOICE associate in xxyyinc.com. You use IP phone A to
place a call to IP phone B. How many RTP streams are required for the call to be successfully
Q: 22 What protocol needs to be enabled on an ATA if an analog telephone is
connected to the ATA?
Q: 23 Please match the CAS component to the office that it will apply.
(6)24 voice channels
(7)30 voice channels
(8)out-of-band signaling in time slot 17
(I)London, United Kingdom
(II)Chicago, United States
A. (I)-(1 4 5 8);(II)-(2 3 7 6)
B. (I)-(2 4 7 8);(II)-(1 3 5 6)
C. (I)-(1 4 7 8);(II)-(2 3 5 6)
D. (I)-(1 3 7 8);(II)-(2 4 5 6)
Q: 24 Jitter is an unwanted variation of one or more characteristics of a periodic
signal in electronics and telecommunications. Jitter may be seen in characteristics such as the interval
between successive pulses, or the amplitude, frequency, or phase of successive cycles. Jitter is a
significant factor in the design of almost all communications links (e.g. USB, PCI-e, SATA, OC-48). In
clock recovery applications it is called timing jitter. Which type of delay can lead to jitter in a voice
A. transmission delay
B. serialization delay
C. CODEC delay
D. queuing delay
Q: 25 What device enables Call Admission Control in a CME environment?